2.6.7内核用modprobe ehci-hcd 出错irq错误！！请大家帮帮忙

kis

ehci_hcd 0000:00:02.2: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 11, pci mem e0878000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
irq 11: nobody cared!
[<c0107a5a>] __report_bad_irq+0x2a/0x90
[<c0107b50>] note_interrupt+0x70/0xa0
[<c0107e00>] do_IRQ+0x130/0x160
[<c0106234>] common_interrupt+0x18/0x20
[<c01079e4>] handle_IRQ_event+0x24/0x70
[<c0107d73>] do_IRQ+0xa3/0x160
[<c0106234>] common_interrupt+0x18/0x20
[<c0122030>] __do_softirq+0x30/0x80
[<c01220a6>] do_softirq+0x26/0x30
[<c0107ddd>] do_IRQ+0x10d/0x160
[<c0106234>] common_interrupt+0x18/0x20
[<c024735f>] pci_bus_read_config_byte+0x5f/0x90
[<e093bb4c>] ehci_start+0x2cc/0x360 [ehci_hcd]
[<c038037a>] preempt_schedule+0x2a/0x50
[<c011ecab>] release_console_sem+0xcb/0xe0
[<c011eafd>] printk+0x10d/0x170
[<c02efdcb>] usb_register_bus+0x14b/0x170
[<c02f4e50>] usb_hcd_pci_probe+0x2b0/0x4e0
[<c024ab82>] pci_device_probe_static+0x52/0x70
[<c024abdb>] __pci_device_probe+0x3b/0x50
[<c024ac1c>] pci_device_probe+0x2c/0x50
[<c029cdaf>] bus_match+0x3f/0x70
[<c029ced9>] driver_attach+0x59/0x90
[<c029d1d5>] bus_add_driver+0xa5/0xc0
[<c029d69f>] driver_register+0x2f/0x40
[<c024ae9c>] pci_register_driver+0x5c/0x90
[<e0876023>] init+0x23/0x30 [ehci_hcd]
[<c0134493>] sys_init_module+0x123/0x260
[<c0106075>] sysenter_past_esp+0x52/0x71

handlers:
[<c02f0bf0>] (usb_hcd_irq+0x0/0x70)
Disabling IRQ #11--------就是这个错误啦！！烦人啊！！！
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
usb 1-1: new high speed USB device using address 2
usb 1-1: control timeout on ep0out
ehci_hcd 0000:00:02.2: Unlink after no-IRQ?  Different ACPI or APIC settings may help.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03e28c0(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
usb 1-1: control timeout on ep0out
usb 1-1: device not accepting address 2, error -110
usb 1-1: new high speed USB device using address 3
usb 1-1: control timeout on ep0out
usb 1-1: control timeout on ep0out
usb 1-1: device not accepting address 3, error -110


上边是modprobe ehci-hcd只后用dmesg输出的信息。我用系统自带的内核就没问题。我的系统是FC2，是不是我的内核配制少了哪项没选啊！！我在google 找了好久。有人和我的问题一样但是就找不到解决方法！我的移动硬盘盒是移动之星的ali芯片！！

7dehao

这个转到硬件版去问问看。

hades

kis兄，我不知道你的2.6.7的内核是编辑成什么模式的，我用的是与你相同的内核，在USB这块的编辑是这样的，看能不能帮你解决问题：
# USB support
#
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_UHCI_HCD=m

#
# USB Device Class drivers
#
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_MIDI is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set

#
# USB Human Interface Devices (HID)
#
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y

#
# USB HID Boot Protocol drivers
#
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set

#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set

#
# Video4Linux support is needed for USB Multimedia device support
#

#
# USB Network adaptors
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set

#
# USB port drivers
#

#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_TEST is not set

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set


按上面的编辑后，数码相机，移动硬盘、USB mouse 、usb keyboard 都能正常使用。
当然移动硬盘这些外挂的东西还要scsi的支持，给个我的完整config给你

kis

在2.6.7下我怎样都是不行，在2.6.5下我用同样的配置却可以！真奇怪！只能期待下个版本的内核啦！
谢谢大家的帮忙！

hades

最初由 kis 发表
在2.6.7下我怎样都是不行，在2.6.5下我用同样的配置却可以！真奇怪！只能期待下个版本的内核啦！
谢谢大家的帮忙！

不会呀，我的没有任何的错误出现，你再试试

kis

就算我usb那里全部都选上scsi都全选了都不可以啊！主要是在挂载ehci-hcd的模块时出现Disabling IRQ #11。如果挂载ohci-hcd就没问题！但是我的移动硬盘就只能用usb1.1来传输！速度好慢的！
现在换回2.6.5就没问题！用的还是2.6.7的config文件。
现在下了个2.6.6回去试下 ！下午我把我的config贴上去给你看看！

hades

最初由 kis 发表
就算我usb那里全部都选上scsi都全选了都不可以啊！主要是在挂载ehci-hcd的模块时出现Disabling IRQ #11。如果挂载ohci-hcd就没问题！但是我的移动硬盘就只能用usb1.1来传输！速度好慢的！
现在换回2.6.5就没问题！用的还是2.6.7的config文件。
现在下了个2.6.6回去试下 ！下午我把我的config贴上去给你看看！

这里是我以前发的贴子，看对你的1.1的USB是不是有用？
http://www.linuxsir.cn/forum.php?mod=viewthread&tid=111908

kis

你上面的一篇文章我有看过拉！不过还是不行。我中午试了2.6.6的内核没问题！还有就是我都是用同一个config的文件。就是2.6.7死活不行！没办法啦！只好将就用着先啦！等2.6.8或我goolg看有没有patch啦！
  非常感谢hades兄！many thanks

bluesky911

你的主板是不是P4P800啊！
我也折腾了好几天了，应该是中断冲突，不仅USB2.0用不了，mount
IDE 硬盘也不行了。（我的系统装在了SATA上）。