安装新硬件之后的问题(PHT370)

功夫猫

新买入一块RAID卡，现在没有那么多硬盘，先当IDE卡用着
但是在起动RH9 LINUX时在partition check时出了点问题：
显示大致如下(来不及记录)
partition check:
hda : hda1 hda2(hda5,hda6,hda7,hda8,.........,hda11)
hde:dma_timer_expiry:dma status==0x21
hde 0 bytes in FIFO
hde timeout waiting for DMA
hde timeout waiting for DMA
hde 0 bytes in FIFO
hde timeout waiting for DMA
hde (__ide_dma_test_irq)called while not waiting


等等信息
大致上就是这样

进入系统后hde一切正常，但是在启动时partition check时(就是出现上面的信息时)等待的时间太长了，感觉十分不爽
这是哪里出了毛病？

功夫猫

dmesg



Linux version 2.4.20-8 (bhcompile@porky.devel.redhat.com) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Thu Mar 13 17:54:28 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000ffec000 (usable)
BIOS-e820: 000000000ffec000 - 000000000ffef000 (ACPI data)
BIOS-e820: 000000000ffef000 - 000000000ffff000 (reserved)
BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65516
zone(0): 4096 pages.
zone(1): 61420 pages.
zone(2): 0 pages.
Kernel command line: ro root=LABEL=/ hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 2500.224 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4993.84 BogoMIPS
Memory: 252924k/262064k available (1347k kernel code, 6708k reserved, 999k data, 132k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: bfebfbff 00000000 00000000 00000000
CPU:             Common caps: bfebfbff 00000000 00000000 00000000
CPU: Intel(R) Celeron(R) CPU 2.00GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf1e60, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Found IRQ 9 for device 00:1f.1
PCI: Sharing IRQ 9 with 00:1d.2
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hdaMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hddMA
HPT370: IDE controller at PCI slot 02:0b.0
PCI: Found IRQ 11 for device 02:0b.0
PCI: Sharing IRQ 11 with 00:1d.7
HPT370: chipset revision 3
HPT370: not 100% native mode: will probe irqs later
HPT37X: using 33MHz PCI clock
    ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hdeMA, hdf:pio
    ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdg:pio, hdh:pio
hda: ST380021A, ATA DISK drive
blk: queue c03c9f40, I/O limit 4095Mb (mask 0xffffffff)
hdd: ATAPI-CD ROM-DRIVE-52MAX, ATAPI CD/DVD-ROM drive
hde: ST3120022A, ATA DISK drive
blk: queue c03ca800, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xb800-0xb807,0xb402 on irq 11
hda: host protected area => 1
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100)
hde: host protected area => 1
hde: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
hde:<4>hde: dma_timer_expiry: dma status == 0x21
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: timeout waiting for DMA
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: (__ide_dma_test_irq) called while not waiting
hde1 hde2 <<4>hde: dma_timer_expiry: dma status == 0x21
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: timeout waiting for DMA
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: (__ide_dma_test_irq) called while not waiting
hde5<4>hde: dma_timer_expiry: dma status == 0x21
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: timeout waiting for DMA
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: (__ide_dma_test_irq) called while not waiting
hde6 >
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 144k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
hde: dma_timer_expiry: dma status == 0x21
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: timeout waiting for DMA
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: (__ide_dma_test_irq) called while not waiting
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 132k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 11 for device 00:1d.7
PCI: Sharing IRQ 11 with 02:0b.0
PCI: Setting latency timer of device 00:1d.7 to 64
ehci-hcd 00:1d.7: Intel Corp. 82801DB USB EHCI Controller
ehci-hcd 00:1d.7: irq 11, pci mem d0849000
usb.c: new USB bus registered, assigned bus number 1

mars_diy

acpi=off

mars_diy

在grub起动项中加入参数 acpi=off

功夫猫

default=1
timeout=10
splashimage=(hd0,9)/boot/grub/splash.xpm.gz
title Red Hat Linux (2.4.20-8)
        root (hd0,9)
        kernel /boot/vmlinuz-2.4.20-8 ro root=LABEL=/ hdc=ide-scsi acpi=off
        initrd /boot/initrd-2.4.20-8.img
title windows 2000
        rootnoverify (hd0,0)
        chainloader +1

这么加了之后还是没有效果

北南南北

是不是把DMA打开了？？
和DMA有关？？

folklore

在bios设一下没有second  harddisk(设为None)如何