|
|
发表于 2005-4-6 16:37:42
|
显示全部楼层
我用的就是IBM ThinkPad R40e， 前面的讨论中我也提过是电源管理的问题，我的解决方法是自己编译kernel, 上级到2.6.10-rc3, 打开acpi 但有几个项一定要编译成模块，否则无法启动！
以下是lscp的信息：
00:00.0 Host bridge: ATI Technologies Inc RS200/RS200M AGP Bridge [IGP 340M] (rev 02)
00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 340M]
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:03.0 Modem: ALi Corporation M5457 AC'97 Modem Controller
00:04.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02)
00:06.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV]
00:0b.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5901 100Base-TX (rev 01)
00:0c.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller
00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c4)
01:05.0 VGA compatible controller: ATI Technologies Inc Radeon IGP 340M
以下是dmesg 信息：
Linux version 2.6.10-rc3-zk (root@kevinzou) (gcc version 3.2.3 20030502 (Red HatLinux 3.2.3-42)) #2 Fri Dec 17 11:23:23 CST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000016f70000 (usable)
BIOS-e820: 0000000016f70000 - 0000000016f7b000 (ACPI data)
BIOS-e820: 0000000016f7b000 - 0000000016f7d000 (ACPI NVS)
BIOS-e820: 0000000016f80000 - 0000000017000000 (reserved)
BIOS-e820: 0000000026f80000 - 0000000027000000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
367MB LOWMEM available.
On node 0 totalpages: 94064
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 89968 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v002 IBM ) @ 0x000f6d90
ACPI: XSDT (v001 IBM TP-1S 0x00001300 LTP 0x00000000) @ 0x16f749ff
ACPI: FADT (v003 IBM TP-1S 0x00001300 IBM 0x00000001) @ 0x16f74b00
ACPI: SSDT (v001 IBM TP-1S 0x00001300 MSFT 0x0100000e) @ 0x16f74cb4
ACPI: ECDT (v001 IBM TP-1S 0x00001300 IBM 0x00000001) @ 0x16f7aec5
ACPI: BOOT (v001 IBM TP-1S 0x00001300 LTP 0x00000001) @ 0x16f7afd8
ACPI: DSDT (v001 IBM TP-1S 0x00001300 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
Built 1 zonelists
Kernel command line: ro root=LABEL=/ vga=792
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1993.298 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 368952k/376256k available (1962k kernel code, 6708k reserved, 802k data,164k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3956.73 BogoMIPS (lpj=1978368)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0800)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 205k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd84c, last bus=4
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Found ECDT
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKI] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC] (gpe 2)
ACPI: Power Resource [PUBS] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0x40b-0x40b has been reserved
pnp: 00:01: ioport range 0x480-0x48f has been reserved
pnp: 00:01: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:01: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:01: ioport range 0xfe10-0xfe11 has been reserved
Simple Boot Flag at 0x35 set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1112778158.854:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
Activating ISA DMA hang workarounds.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.4
acpiphp_ibm: ibm_acpiphp_init: acpi_walk_namespace failed
vesafb: framebuffer at 0xf8000000, mapped to 0xd7880000, using 4608k, total 16384k
vesafb: mode is 1024x768x24, linelength=3072, pages=6
vesafb: protected mode interface info at c000:4f49
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ibm_acpi: IBM ThinkPad ACPI Extras v0.8
ibm_acpi: http://ibm-acpi.sf.net/
Real Time Clock Driver v1.12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
tg3.c:v3.14 (November 15, 2004)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 11 (level, low) -> IRQ 11
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(BCM95901A50) rev 3001 PHY(5705)] (PCI:33MHz:32-bit) 10/100BaseT Ethernet 00:06:1b:df:cc:da
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:0f.0
ACPI: PCI interrupt 0000:00:0f.0[A]: no GSI - using IRQ 0
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8080-0x8087, BIOS settings: hda MA, hdb:pio
ide1: BM-DMA at 0x8088-0x808f, BIOS settings: hdcMA, hdd:pio
Probing IDE interface ide0...
hda: FUJITSU MHT2030AT, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CD-224E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 52196228 sectors (26724 MB)
native capacity is 58605120 sectors (30005 MB)
hda: Host Protected Area disabled.
hda: 58605120 sectors (30005 MB) w/2048KiB Cache, CHS=62016/15/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 >
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PS/2 Generic Mouse on isa0060/serio1
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI wakeup devices:
LID SLPB PCI0 USB0 AC97 LAN
ACPI: (supports S0 S3 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Freeing unused kernel memory: 164k freed
EXT3 FS on hda6, internal journal
Adding 257000k swap on /dev/hda5. Priority:-1 extents:1
ip_tables: (C) 2000-2002 Netfilter core team
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c037f2c0(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
eth0: no IPv6 routers present
thinkpad: I have registered to handle major: 10 minor: 170.
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 11 (level, low) -> IRQ 11 |
|
IP卡
狗仔卡
发表于 2005-4-6 13:47:34
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
发表于 2005-4-6 14:20:25