ifplugd 设定问题 (己解决)

cliffordli

本来按手册这好象是很容易的事，但到我机上好象不太好使。请问大家是怎么设定的?

按照手册， 在/etc/conf.d/net中我是这样写的。
~ $ cat /etc/conf.d/net
#DHCP
# eth0 setting
config_eth0=(        "noop""dhcp")
dhcpcd_eth0="-t 10"
fallback_eth0=("null""apipa")
dhcp_eth0="release nodns nontp nonis"

#Wlan0 setting
modules=("iwconfig")
config_wlan0=("noop""dhcp")
fallback_wlan0=("null""apipa")
dhcp_wlan0="release nodns nontp nonis"
preferred_aps=("MyNet")
associate_order=("preferredonly")
#associate_order=("any" "preferredonly" forceprefered forcepreferredonly forceany")
#===========================================
#Monitoring
ifplugd_eth0="..."
ifplugd_wlan0="--api-mode=wlan"
#===========================================

但是这个ifplugd好象根本不起作用. 对eth0它是:

~ $ sudo /etc/init.d/net.eth0 restart
* Bringing down interface eth0
*   Loaded modules: ip6to4 dhcpcd udhcpc dhclient system pppd iproute2 ifconfig ssidnet wpa_supplicant iwconfig ipppd ifplugd netplugd macnet macchanger ccwgroup tuntap br2684ctl bonding arping apipa adsl
*   Stopping ifplugd on eth0...
/usr/sbin/ifplugd'                                                        [ ok ]
* Bringing up interface eth0
*   Loaded modules: adsl apipa arping bonding tuntap ccwgroup macchanger macnet ifplugd iwconfig ssidnet iproute2 pppd system dhcpcd ip6to4
*   Configuring eth0 for MAC address 11:22:33:44:55:66...                 [ ok ]
*   Starting ifplugd on eth0...
*   Detaching to start `/usr/sbin/ifplugd'...                             [ ok ]
*     Backgrounding ...
* WARNING: net.eth0 has started, but is inactive

对元线网卡它是:

~ $ sudo /etc/init.d/net.wlan0 restart
* Bringing down interface wlan0
*   Loaded modules: ip6to4 dhcpcd udhcpc dhclient system pppd iproute2 ifconfig ssidnet wpa_supplicant iwconfig ipppd ifplugd netplugd macnet macchanger ccwgroup tuntap br2684ctl bonding arping apipa adsl
*   Stopping dhcpcd on wlan0...                                           [ ok ]
* Bringing up interface wlan0
*   Loaded modules: adsl apipa arping bonding tuntap ccwgroup macchanger macnet ifplugd iwconfig ssidnet iproute2 pppd system dhcpcd ip6to4
*   Configuring wlan0 for MAC address AA:BB:CCD:EE...                [ ok ]
*   ifplugd does not work with wireless
*   Configuring wireless network for wlan0
*   Scanning for access points
*     Found "MyNet" at AA:BB:CCD:EE, managed
*   Connecting to "MyNet" in managed mode (WEP Disabled)...              [ ok ]
*     wlan0 connected to SSID "MyNet" at AA:BB:CCD:EE
*     in managed mode (WEP disabled)
*   Configuring wlan0 for SSID MyNet...                                  [ ok ]
*   noop...                                                               [ ok ]
*   dhcp...
*     Running dhcpcd...
wlan0: dhcpcd 4.0.7 starting
wlan0: broadcasting for a lease
wlan0: timed out
wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.lease'
wlan0: checking 169.254.54.25 is available on attached networks
wlan0: using IPv4LL address 169.254.54.25                                 [ ok ]
*     received address 169.254.54.25/16  
....

zhou3345

无线网络我现在用wicd，挺好用的。

cliffordli

我没有装wicd, 在/etc/conf.d/net里面设定好就能连上了，这个ifplugd使用应该与wicd无关吧。

这个ifplugd让我每次开机都要等十来秒，很不爽。

cliffordli

研究了一圈回来，查了几篇wiki. 改了一下/etc/conf.d/net 和 /etc/ifplugd/ifplugd.action, 无线网卡终于不再时断时续了, 现在emerge -uDN的下载速度可达220k/s以上.

/etc/conf.d/net改成了：
=========================
#Wlan0 setting
modules=("iwconfig")
rate_wlan0=("5.5M auto")   #此句新加
config_wlan0=("noop""dhcp")
fallback_wlan0=("null""apipa")
dhcp_wlan0="release nodns nontp nonis"
preferred_aps=("MyNet")
associate_order=("preferredonly")

ifplugd_eth0="..."
ifplugd_wlan0="--api-mode=wlan"
plug_timeout="10"   #此句新加

把/etc/ifplugd/ifplugd.action里面这段改成
case "$2" in
    up)
        if [ "${INITNG}" = "yes" ]
        then
            ARGS="-u net/$1"
        else
            /etc/init.d/net.wlan0 --quiet stop  #此句新加
            ARGS="--quiet start"
        fi
        ;;
    down)
        if [ "${INITNG}" = "yes" ]
        then
            ARGS="-d net/$1"
        else
            /etc/init.d/net.wlan0 --quiet start   #此句新加
            ARGS="--quiet stop"
        fi
        ;;
    *)
        echo "$0: wrong arguments" >&2
        echo "Call with <interface> <up|down>" >&2
        exit 1
        ;;
esac

现在看ifplugdstatus的输出是
~ $ sudo ifplugstatus
lo: link beat detected
eth0: unplugged
tunl0: unplugged
gre0: unplugged
sit0: unplugged
wmaster0: link beat detected
wlan0: link beat detected
ppp0: link beat detected